Illuminated SANlight STIXX 6-150 141 W LED grow light with six lighting modules, suspended against a dark green background

SANlight STIXX 6-150 141 W LED grow light shown from two different angles, illuminated and suspended with hanging cables

SANlight STIXX 6-150 Full-Spectrum LED Grow Light, 141 W

Data sheet / description

The SANlight STIXX 6-150 Full-Spectrum LED Grow Light, 141 W, delivers 381 µmol/s PPF and has IP68 protection for indoor growing areas 150 cm deep. Drivers, cables and accessories are sold separately.

SANlight STIXX 6-150 Full-Spectrum LED Grow Light, 141 W – Product data
Brand	SANlight
Model	STIXX 6-150
Type	Full-spectrum LED grow light
Power consumption	141 W
Photon flux (PPF)	381 µmol/s in the 400–780 nm range
LED modules	6
Designed growing area depth	150 cm
Beam angle	90° / 135°
Ingress protection rating	IP68
Dimensions (L × W × H)	1366 × 85 × 16.9 mm
Weight	1.98 kg
Manufacturer part number	AA5050
Package contents	Light without driver, cables or accessories

Product number

STIXX-6-150-LED

Manufacturer

sanLight

SANlight GmbH & SLT GmbH
Montafonerstrasse 14
6780 Schruns

Austria

support@sanlight.com

www.sanlight.com

Weight

1.98 kg

Not in stock

162.90 €

(0)

Leave a review!

Recommend to a friend

Print product page

Product description

SANlight STIXX 6-150 full-spectrum LED grow light with cable suspension

SANlight STIXX 6-150 Full-Spectrum LED Grow Light, 141 W

The SANlight STIXX 6-150 is a linear full-spectrum LED grow light with six modules. It is designed for indoor growing areas 150 cm deep and delivers a photon flux of 381 µmol/s at a power consumption of 141 W.

If you want to light longer rows of plants or larger crops, the slim bar can be incorporated into a modular system. The light and power supply are selected separately, allowing you to match the setup to the available area and your preferred arrangement.

Full spectrum and broad light distribution

The full-spectrum LEDs use 90/135° optics. The different beam widths in two directions matter when planning the position of the bar: before installation, consider how the light should be directed towards your growing area.

The design depth of 150 cm provides a guide when choosing the model. The illuminated width, however, depends on the arrangement and number of lights. Also take plant height and the spacing between bars into account when planning.

Low-profile design for shelving and larger crops

The LED bar measures 1366 × 85 × 16.9 mm and weighs 1.98 kg. Its actual length is therefore 136.6 cm; the number 150 in the model name refers to the intended growing area depth. Check the available installation space against the actual dimensions.

The low-profile design is suitable for installations with limited height, vertical farming, and vegetative and mother plant areas. Still allow enough room for plant development, secure mounting and easy access to the light.

Choose the STIXX driver to suit your setup

The STIXX 6-150 is offered as a light without a driver, cables or other accessories. To operate it, you need a STIXX driver approved for this model and the corresponding wiring. Gather these components before installation.

Only identical lights from the same model series may operate on a shared driver. The permitted combination determines the available power. Use the SANlight driver overview when selecting components, rather than judging suitability from the wattage alone.

Installation and first use

First decide where to position the light and driver. Keep connections accessible and route cables without tension. Secure the bar reliably against falling and check the suspension before switching it on.

Inspect the components for visible damage. Make the connections with the mains power disconnected; connect the driver to the mains only once the complete setup is assembled.

Choose the installation position and an approved driver combination.
Securely mount the light and maintain the required clearances.
Connect the LED lights to the driver using the appropriate cables; seal open DC connections with end plugs.
Check the connections and mounting, then connect the mains power.

Keep the optics clean with gentle care

Disconnect the system from the mains before cleaning. Use a soft, non-abrasive cloth with distilled water for the optics. Avoid cleaning agents and vigorous rubbing so that cleaning does not scratch the surface.

Also check the suspension and cable routing at the same time. Keeping connections easily accessible allows you to include these visual checks in the regular care of your installation.

Safe indoor use

Maintain at least 15 cm clearance from the illuminated area and surrounding objects. Provide airflow, do not cover the light and avoid direct contact with plant parts. Do not look directly into the LEDs when they are on.

IP68 applies to the light. The driver’s mains-side plug is not waterproof and must be protected from moisture and water. Always disconnect the mains before working on the system; do not continue to operate damaged components.

Technical specifications

Brand	SANlight
Model	STIXX 6-150
Type	Full-spectrum LED grow light
Power consumption	141 W
Photon flux (PPF)	381 µmol/s in the 400–780 nm range
LED modules	6
Designed growing area depth	150 cm
Beam angle	90° / 135°
Ingress protection rating	IP68
Dimensions (L × W × H)	1366 × 85 × 16.9 mm
Weight	1.98 kg
Manufacturer part number	AA5050
Package contents	Light without driver, cables or accessories

Why choose the STIXX 6-150?

The STIXX 6-150 combines six LED modules with a long, low-profile design for areas 150 cm deep. This is practical if you want to plan a linear lighting arrangement for larger crops.

An approved driver, suitable wiring and careful installation create a setup with individual components matched to your installation.