SANlight STIXX 4-100 94 W LED grow light with silver aluminium housing, horizontally suspended against a dark green background

Illuminated SANlight STIXX 4-100 94 W LED grow light suspended with hanging cables, black power cord and blue connector ring

SANlight STIXX 4-100 Full-Spectrum LED Grow Light, 94 W

Data sheet / description

The SANlight STIXX 4-100 Full-Spectrum LED Grow Light, 94 W, delivers 254 µmol/s PPF and has IP68 protection for indoor growing areas 100 cm deep. Drivers, cables and accessories are sold separately.

SANlight STIXX 4-100 Full-Spectrum LED Grow Light, 94 W – Product data
Brand	SANlight
Model	STIXX 4-100
Type	Full-spectrum LED grow light
Power consumption	94 W
Photon flux (PPF)	254 µmol/s in the 400–780 nm range
LED modules	4
Designed growing area depth	100 cm
Beam angle	90° / 135°
Ingress protection rating	IP68
Dimensions (L × W × H)	896 × 85 × 16.9 mm
Weight	1.35 kg
Manufacturer part number	AA5030
Package contents	Light without driver, cables or accessories

Product number

STIXX-4-100-LED

Manufacturer

sanLight

SANlight GmbH & SLT GmbH
Montafonerstrasse 14
6780 Schruns

Austria

support@sanlight.com

www.sanlight.com

Weight

4.00 kg

114.90 €

(0)

Leave a review!

Recommend to a friend

Print product page

Product description

SANlight STIXX 4-100 full-spectrum LED grow light with cable suspension

SANlight STIXX 4-100 Full-Spectrum LED Grow Light, 94 W

The SANlight STIXX 4-100 is a full-spectrum LED grow light with four modules for indoor growing areas 100 cm deep. At a power consumption of 94 W, it delivers a photon flux of 254 µmol/s.

The linear bar can be planned into medium-sized growing areas and shelving systems. If you want to build a lighting setup from several individual lights, the separate power supply and slim design provide a clearly structured starting point.

Broad light distribution through asymmetric optics

The asymmetric 90/135° optics distribute full-spectrum light at different beam angles in two directions. Align the bar deliberately towards the growing area and account for its orientation when planning several lights.

The STIXX 4-100 is designed for a growing area depth of 100 cm. The width of your growing area and the distribution of the plants also influence how you arrange the bars. The model designation alone therefore does not replace planning the entire illuminated area.

Compact dimensions for versatile arrangements

At 896 × 85 × 16.9 mm, the bar has a low profile and weighs 1.35 kg. Its actual length of 89.6 cm differs from the intended growing area depth of 100 cm. Check mounting points and available space against the product dimensions.

The manufacturer lists top lighting, vegetative and mother plant areas, and vertical farming as possible uses. If you use the bar in a compact installation, also allow space for plant development, safe clearances and access for maintenance.

Modular power supply with a matching STIXX driver

The STIXX 4-100 is supplied without a driver, cables or accessories. For its power supply, you need a STIXX driver designed for this model. Gather the necessary connecting cables and suitable mounting hardware before starting assembly.

Only identical STIXX lights from the same model series may operate together on one driver. Select a combination approved in the SANlight driver overview. If the number of lights changes, check the planned power supply again.

Installation and commissioning

First decide on the bar’s position, the driver’s location and the cable routes. Keep connections accessible and avoid tension on the cables. Secure mounting helps prevent the light from falling accidentally.

Inspect all components for visible damage. Keep the mains disconnected during assembly. Switch the system on only once the light and driver are fully connected and the mounting has been checked.

Decide on a suitable installation position and an approved driver combination.
Securely mount the light and check the specified clearances.
Connect the LED lights to the driver; seal open DC connections with end plugs.
Check the setup and then connect the mains.

Gentle cleaning and regular checks

Disconnect the mains before every cleaning. SANlight recommends a soft, non-abrasive cloth with distilled water for the optics. Do not use cleaning agents on them and avoid scratching them through pressure or rough materials.

Also use cleaning as an opportunity to visually inspect the suspension and cables. If you have moved the bar, check the mounting and cable routing again before returning the lighting to operation.

Safety around light and power connections

Maintain at least 15 cm clearance from the illuminated area and surrounding objects. Provide airflow, do not cover the bar and avoid contact with plant parts. Do not look directly into the LEDs when they are on.

IP68 applies to the light. The driver’s mains-side plug is not waterproof and needs protection from moisture and water. Disconnect the system from the mains before working on it; if damage is visible, the affected parts must not be used again.

Technical specifications

Brand	SANlight
Model	STIXX 4-100
Type	Full-spectrum LED grow light
Power consumption	94 W
Photon flux (PPF)	254 µmol/s in the 400–780 nm range
LED modules	4
Designed growing area depth	100 cm
Beam angle	90° / 135°
Ingress protection rating	IP68
Dimensions (L × W × H)	896 × 85 × 16.9 mm
Weight	1.35 kg
Manufacturer part number	AA5030
Package contents	Light without driver, cables or accessories

Why choose the STIXX 4-100?

The STIXX 4-100 combines four LED modules, full-spectrum light and a low profile for growing areas 100 cm deep. The linear format suits a deliberately planned arrangement above or within a growing system.

By selecting suitable drivers, cables and mounting hardware, you obtain a clearly arranged lighting component for your indoor installation.